Skip to main content

Site Navigation

Your Account

Choose Language

  1. Push bowden tube into coupling Push other end of bowden tube into Bondtech BMG Bowden tube in couplings
    • Push bowden tube into coupling

    • Push other end of bowden tube into Bondtech BMG

    • Bowden tube in couplings

  2. 3-Wire BLTouch Extension (1x)
    • 3-Wire BLTouch Extension (1x)

    • Single Female Dupont Connector (1x)

    • Double Female Dupont Connector (2x)

  3. Use small flathead screwdriver to lift tab While holding tab up, slide wire out Repeat last step for all three wires
    • Use small flathead screwdriver to lift tab

    • While holding tab up, slide wire out

    • Repeat last step for all three wires

  4. Insert orange wire into connector Pin orientation is important. when inserted properly it will make a small click and you will not be able to pull out Insert brown and red wire into double connector
    • Insert orange wire into connector

    • Pin orientation is important. when inserted properly it will make a small click and you will not be able to pull out

    • Insert brown and red wire into double connector

    • Finished extension with correct connectors

  5. Zip-Ties
    • Zip-Ties

    • Wire Clips (No Zip-tie) (11x)

    • Wire Clip (Zip-Tie) (6x)

  6. Plug in extension cables
    • Plug in extension cables

    • It is important to make sure all wires are aligned with their matching colors

  7. Insert Zip-Tie Fasten thirmistor and hotend fan wire with Zip-Tie Plug  in (un labeled black and red extension)  into hotend fan and (green label) extension into hotend thermistor
    • Insert Zip-Tie

    • Fasten thirmistor and hotend fan wire with Zip-Tie

    • Plug in (un labeled black and red extension) into hotend fan and (green label) extension into hotend thermistor

  8. Plug (red label) extension into extruder motor Plug in (blue label) extension cable into part cooling fan
    • Plug (red label) extension into extruder motor

    • Plug in (blue label) extension cable into part cooling fan

  9. Bundle all print carriage wires Wire bundle: Extruder Motor Wire, Part Cooling Fan Wires, Hotend Fan Wire, BLTouch Wires, Thermistor Wires and Hotend Wires Feed cables into sleeve
    • Bundle all print carriage wires

    • Wire bundle: Extruder Motor Wire, Part Cooling Fan Wires, Hotend Fan Wire, BLTouch Wires, Thermistor Wires and Hotend Wires

    • Feed cables into sleeve

    • Showing cables pulled all the way through sleeve

  10. Insert Zip-Ties into Zip-Tie Mounts on Carriage Fasten sleeve to carriage with Zip-ties
    • Insert Zip-Ties into Zip-Tie Mounts on Carriage

    • Fasten sleeve to carriage with Zip-ties

  11. Insert Zip-Ties into Printed Wire Clips Snap into extrusion slot Repeat last step
    • Insert Zip-Ties into Printed Wire Clips

    • Snap into extrusion slot

    • Repeat last step

  12. Plug (brown label) wire into XY motor on side with power supply. Plug (grey label) wire into XY motor on control board side Snap Wire Clips on Prepare wires to be Zip-Tied
    • Plug (brown label) wire into XY motor on side with power supply. Plug (grey label) wire into XY motor on control board side

    • Snap Wire Clips on

    • Prepare wires to be Zip-Tied

    • Fasten sleeved cables and both XY motor cables with Zip-Tie

  13. Snap clips with zip-tie into slot Fasten Heated bed wire to bed frame with zip-tie Wired to bed frame
    • Snap clips with zip-tie into slot

    • Fasten Heated bed wire to bed frame with zip-tie

    • Wired to bed frame

  14. Snap wire clip with zip-tie into slot Plug bed cables into board Refer to wiring diagram on step 16
    • Snap wire clip with zip-tie into slot

    • Plug bed cables into board

    • Refer to wiring diagram on step 16

    • Fasten bed cable with zip-ties

  15. Plug  (orange label) extension into left Z motor. Plug  (purple label) extension into Right Z motor Z Motors wire paths
    • Plug (orange label) extension into left Z motor. Plug (purple label) extension into Right Z motor

    • Z Motors wire paths

    • Wire Clips

  16. At this point all wires have been wired up  until the board. Its time to plug it all in!
    • At this point all wires have been wired up until the board. Its time to plug it all in!

    • It's possible most wires can be plugged in backwards. Pay close attention to polarity

    • Incorrect input power or heated bed polarity can ruin board. Red -positive Black-negative

    • BLTouch wires are plugged into the 1st row and 4th with two open pins between

    • Rotate board diagram

  17. I like to start with the motor wires Fallowed by the fans thermistor and heater cartridge And last the BLTouch
    • I like to start with the motor wires

    • Fallowed by the fans thermistor and heater cartridge

    • And last the BLTouch

  18. Back view of wires feeding into Duetwifi enclosure Cable management inside enclosure Finished wiring with cover snapped into place
    • Back view of wires feeding into Duetwifi enclosure

    • Cable management inside enclosure

    • Finished wiring with cover snapped into place

  19. Be careful of cutting wires accidentally
    • Be careful of cutting wires accidentally

Finish Line

2 other people completed this guide.

Leland Crowther

Member since: 06/25/2018

3,166 Reputation

17 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 1

Past 30 Days: 3

All Time: 124